Full Kit
Your kit should
include the following:
One white TMI LED
head light, One TMI wire harness (WE-6R-2) with two red rectangle LED
lights, One TMI wire harness with one red round seat light with 3M sticker,
One TMI wire harness (WE-6Y-4)with two amber rectangle LED lights with 3M
sticker, One TMI wire harness (WE-6UV-3) with three UV rectangle LED lights
with 3M stickers, Five TMI blue circle LED lights cable with 3m sticker
with connector on the ends to connect into the red, amber and UV wire
harness, One 7.5AH rechargeable AGM
battery with no memory for long life and recharge cord, One Battery Tender
battery charger, One TMI Nylon battery bag, One pack three pcs
of double back Velcro straps to hold the battery and controller inside the
battery bag to the bicycle, One wireless light controller with a pocket remote
that can mount to bicycle or placed in pocket, which can turn on and off lights
with no switches up to 250 feet way, 3 extra 3M rectangle stickers to cut and
use for sticking cables to bicycle.
1.) Attach
controller power cable with Red and Black wires to battery terminals.
a. Red wire with red or yellow
connector to red (+) battery terminal.
b. Black wire with blue or black connector
to black (-) battery terminal.
2.) Now remove cover of pock remote and Insert 12V
battery and place cover back on and then make sure when you press each button to make
sure LED lights up on the remote to show it is working. After you see the
pocket remote is working please insert the two small screws in the back and
tighten down holding the back in front case together.
((WARNING)) Mount battery
with controller in battery bag under handle bar using TMI’s
back to back Velcro straps holding battery to bicycle. Make sure battery
terminals are facing forward away from the handle bar or any metal or aluminum
to prevent any shorts or damage to terminals.
3.) Attach
all light to cables, which there are 3 zones and make sure they all work.
To install lights press black locking
tab and carefully insert lights into connector and do not brake locking tab off
or bend connector pins.
Zone 1 button #1 is for the
headlight, which has only one wire with a male connector
Zone 2 button #2 is the short Y-cable for the two amber rectangle
lights, two red rail lights and one red
seat light.
Zone 3 button #3 is for the five blue circle ground effect and the three purple UV down
bar lights.
Button #4 turns
turn off all lights OFF at one
time whenever pressed.
There are five black cables
to attach lights to the bicycle that will need to have all light attached to
them using the simple small Black plug-and-play connectors and the headlight
that has the cable permanently attached to the light with one Black
plug-and-play connector at the end of the cable to attach to the connector at
the controller.
To install lights press black locking
tab and carefully insert lights into connector and do not brake locking tab off
or bend connector pins. If you brake locking tab off
use black electrical tape to hold connectors together.
Before installing cable with light you must make sure how you want the cables
to run on the your bicycle before pealing and sticking attaching the 3M tape to
the light and to the bicycle. DO NOT REMOVE THE PROTECTIVE COVERING FROM ANY
OF THE 3M TAPE (STICKERS) YET. You must make sure how
you want to run the cable which will reach the battery and controller in the
battery bag mounted in the front under the handle bar.
You must also make sure the
cables that you are going to attached to the bicycle will not be rubbing the
bicycle tire and if you have a rear gear speed bicycle the blue circle light
must not be rubbing on the chain when it is in the smallest gear on the rear
wheel.
4.) After
checking placement of the lights on the bicycle and assuring yourself where you
want the lights to be installed, now place all lights with black cables on the
ground or table.
5.) At
this point in time you need to use a clean rag with 99% alcohol to clean the
back surface of all the LED lights, so they are dirt free and oil free. Make sure after cleaning ALL lights you do not touch the back side of the light with
your fingers or hand, because this will leave oils or dirt from your hand or
fingers on the back of the lights, which will prevent the 3M sticker from
securely bonding to
the surface.
6.) After
all lights are fully cleaned you need to take the 99% alcohol and a clean rag
and clean the surface areas where the all LED lights will be attached to the
bicycle frame. It is very critical that
you clean the surface areas of the frame using the 99% alcohol, which will allow
the sticker to bond to the surface securing all the lights in place. DO NOT TOUCH CLEANED SURFACE AFTER
CLEANING.
7.) The
first light you can be secure in place is the white LED headlight, but you will
need to remove the white reflector from the reflector bracket by unscrewing the
reflector or unsnapping
it from the bracket and then using the screw provided with the
white headlight to mount the white 18 LED headlight to the same bracket where reflector
was removed making the white headlight a retro fit install using the same
mounting bracket. (No sticker)
8.) The
next light you would need to mount is the rear seat light by removing the red
reflector and mounting the red circle light onto the rear seat bracket using
the 3M circle tape provided and running the cable up to the controller mounted
under the handle bar in a straight line as possible, so you do not run out of
cable length.
9.) The
next lights to mount are the Front Amber running lights. After both amber
lights are fully cleaned, pick up one 3M rectangular shape tape and peel off
the protective covers on one side Only and fold over
long ways to double up the thickness of the 3M tape.
Make sure you fold it and press tape together so not to trap air between by
working from one end to the other end of the sticker. Next, peel back only one half of the
rectangular double thickness tape leaving the other half still stuck to the 3M
tape.
Place the one half peeled back
rectangular shape tape onto each amber light leaving
the other half of the tape protection still attached to the 3M sticker.
10.) Now pick up two pieces of the 10” Long wire Circle 3M sticker
tape peel off only one side and attach it to the bottom of the cleaned area of
the blue circle lights. Please be careful not to touch the back side of the
circle lights leaving oil residue or dirt on the back to light which would
prevent the 3M sticker sticking securely to light.
11.) Before attaching the Amber
Front lights to the bicycle frame front fork you must attach the 10” long cable
blue circle lights under both front forks with each wire coming out the back. Make
sure you run the cable up the back of bicycle front forks so that they do not
get into the spokes or wheel.
12.) If
your bicycle has shocks please run cable behind front brake
mount. leave enough cable allowing the wire
cable to bend and flex freely when the shock is compressed and released. Any
loose cable can be secured to the bicycle using extra 3M molding tape provided in the
kit or can be purchased at AutoZone. You can also use any colored
plastic wire ties sold at Home Depot or Lowes or most
hardware stores nationwide to secure cable to bike.. (See Photo below)
13.) When
you are sure about how to run the amber light cables then run the cable as you
like and then hook blue light to the connector FIRST on the amber cable and then hook amber light to connector
cable. Next make sure all slack is taken out of the blue cable as
possible and place amber just under the front brake mount . When you are ready Peal off the
remaining 3M rectangle tape on each rectangle amber light one at a time and
mount the amber light where light facing
straight forward and press firm and hold for 15 seconds.
Now you can do the other side and make sure both lights are in the same
position so they look even across. If you need to adjust light, with clean
hands pull light and sticker off keeping the tape on the light and pull away
from frame and re-position until you are happy with the look and attach and
press and hold for 15-20 seconds.
14.) Now you are going to secure the red rear rail
lights. After both RED lights are fully cleaned, MAKE SURE THE WIRE COMES OUT THE SIDE WITH
THE SMALL SLOT AND WHEN MOUNTING THE SLOT AND WIRE FACES INSIDE FORWARD OR
BACKWARDS TOWARDS THE FRAM. Now pick up one 3M rectangular shape
tape and peel off the protective covers on one side only and fold over long
ways to double up the thickness of the 3M tape like seen above. Next, peel back
only one half of the rectangular double thickness tape leaving the other half
still stuck to the 3M tape. Like see above and place the one half peeled back
rectangular shape tape to each Red rear rail light leaving the other half of
the tape protection still attached.
Now pick up two pieces of
the Circle 3M sticker tape peel off only one side and attach it to the bottom
of the cleaned area of the blue circle lights. Please be careful not to touch
the back side of the circle lights leaving oil residue or dirt on the back of
the light which can prevent the 3M sticker sticking securely to light.
Before attaching the Red rear rail lights to the bicycle rear frame make sure
you are sure on how you want your wires run up to the front battery and
controller. If the bicycle has a rear shock or spring suspension please make
sure the cable runs down towards the hinged area at the peddle crank away from
the shock spring, so when the rear frame moves up and down it bend and move
freely and will not interfere by pulling on the wire cable when the wire cable
is running through the hinged area.
Please look at a sample
drawing and photos below provided on how you can run the rear rail cable. Any loose cables can be secured to the bicycle
using the 3M tape provided or can be purchased from AutoZone. You can also use
colored plastic wire ties sold at Home Depot or Lowes
or almost all hardware stores nationwide to secure cables.
15.) Now
to install the ultraviolet purple lights on the down bar.
After three purple UV lights
are fully cleaned, pick up one 3M rectangular shape tape peel off the
protective covers on one side only and fold over long ways to double up the
thickness of the 3M tape. Next, peel back only one half of the rectangular
double thickness tape leaving the other half still stuck to the 3M tape. Place
the one half peeled back rectangular shape tape to
each Purple UV light leaving the other half of the tape protection still
attached.
Now pick up one piece of the
Circle 3M sticker tape peel off only one side and attach it to the bottom of
the cleaned area of the blue circle light and please be careful not to touch
the back side of the circle lights leaving oil residue or dirt on the back to
light which would prevent the 3M sticker sticking securely to light.
After all 3M stickers are
attached to all lights peel off the protective cover first on the circle light
and place the blue circle light under the peddle crank.
Next hold number three and number one purple UV light up onto the down
bar making sure they fit in the area between the peddle crank and the steering.
Once you are happy with number one in number three placement of the purple UV
lights please peel off the protective paper on the sticker on #3 purple and attach
the number three closest too the blue circle light on the peddle crank. After
number three purple UV is securely attached hold the cable up again were all
the lights joined together keeping wire straight and attach number two purple
UV light to the down bar after attaching number two light attach number one
purple UV light and then route the cable up towards the battery and the
controller.
16.) Make
sure all cables are secure and will not rub tires, get in spokes, chain and
cables are free to move bend left are right at the battery bag. Please make sure the battery charge cable is
out of the battery bag so you can hook up the Battery Tender Charger when
battery gets low. You will know when
battery is getting low when the white head light starts to get dim.
Make sure the cable are tucked away inside the battery bags and the cover
closed.
You may have to loop wires around the controller box, so they all fit inside.
To close bag cover tight you
will need to use pliers and pull on the cover strap to draw cover to close
tight. Please push on bag cover and pull on strap with pliers, so you do not
break clip or tear the bag.
Please do not over do it!
